NEW FUNCTION IN 3-Series CLOCK
The ability to wirelessly read and save the timer configuration via an Android phone equipped with an NFC communication module.

Operation
The astronomical timer on the basis of information about the current date, geographical coordinates of the place of its installation, automatically determines daily programmed points of switching on and off the lighting. The exact time of switching on and off is determined by calculating the position of the sun in relation to the horizon, and allows you to select one of three control options (the moment of light switching on and off is set independently):
1. Astronomical sunset and sunrise
2. Dusk / civil dawn
3. Correction - individual correction of programmed switch-on and switch-off points by the user: angular or temporal.

Clock functions
AUTOMATIC OPERATION - automatic operation according to programmed switch-on and switch-off points of the contact [switched-on symbol on the display on the left].
Semi-automatic operation - possibility of manual contact switching on/off during automatic operation. The change will be in effect until the next ON/OFF resulting from the automatic operation cycle [flashing symbol on the left-hand display].
NOTE: In semi-automatic operation, the contact position is opposite to that resulting from the program cycle (i.e. at night the contact is off and during the day it is on). Semi-automatic operation works only until the end of the current automatic operation cycle, e.g., entering semi-automatic mode during the day will switch on the light until the program switching time resulting from the astronomical cycle. Then the timer returns to automatic operation (and the light continues to stay on until dawn).
MANUAL OPERATION -[ON] permanently energize the contact (items 1-5) or[OFF] permanently de-energize the contact (items 1-6) with AUTOMATIC OPERATION mode off. [no symbol on the left-hand display].
ASTRONOMIC sunrise and sun set - moments when the center of the solar disk touches the horizon (parameter h= -0.583°). For the sake of simplification of calculations, a deviation of a few minutes from the data determined by the "HM Nautical Almanac Office" is allowed.
NOTE : The advantage of setting the on/off moment as a function of the position of the solar disk is that it is insensitive to changes in the duration of dusk/dawn for different seasons, so that the on/off moment always occurs for the same level of brightness.
DUSKNOW and CIVIC D AWN - also calendar - the phase of sunset,
in which the center of the solar disk will be no more than 6 angular degrees below the horizon (the solar disk viewed from Earth has a diameter of about half a degree). At this time, the brightest stars and planets appear in the sky (if the air is clear) (the "Evening Star," the "first star" on Christmas Eve). Due to the scattering of light in the atmosphere, there is still generally enough sunlight that it is still sufficient for normal outdoor activities without artificial light sources. Civil dawn (also calendar dawn) - the time before sunrise when the center of the sun's disc is already more than 6 ° below the horizon line.
PROGRAMMABLE ON and OFF POINT - the times of contact on (items 1-5) and contact off (items 1-6) determined based on the selected control option: astronomical east/west or dawn/civil twilight and location.
CONFIGURATION - providing LOCALIZATION and designating the PROGRAMMABLE ON and OFF POINTS.
LOCATION - geographic coordinates and time zone of a locality relatively close to the place of installation of the clock. The memory defines locations and time zones of about 1500 localities from 51 countries of the world. It is possible to enter your own settings in the form of geographic location and time zone (UTC).
CODE OF COORDINATES - assigned geographic coordinates for the listed cities to make it easier to specify the location (cities and their assigned codes are given in the table at the back of the manual). The full list of countries and their corresponding codes can be found (at the bottom of the page) in the downloads under the name: Coordinate Code Table.
CORRECTION - acceleration or delay of on/off times in relation to the astronomical time points of sunrise and sunset:
±15° - angular correction for the time of switch-on relative to the position of the center of the sun's disk relative to the horizon
±180 min. - time correction for the moment of switching on as a time offset relative to sunrise/sunset.
DST - Daylight Saving Time - the global name for daylight saving time (free translation: sunlight-saving time). A function to disable automatic time change.
AUTOMATIC TIME CHANGE - Change of time from winter to summer time. Option to work with or without automatic change. The controller is equipped with a time zone selection function so that the switching time is in accordance with the local time.
DATE LIVEPAGE - preview of the set date (OK).
PROGRAMMABLE ON/OFF PO INTS AND LOCATION LIGHTING - possibility to preview the current time of contact switching on and off, as well as the set location (geographical coordinates are displayed) and UTC time zone (in date preview mode, successive presses of +/? buttons.
NFC FREE COMMUNICATION - Possibility to read and save the timer configuration wirelessly via an Android phone equipped with an NFC communication module.
PCZ CONFIGURATOR APLICATION - Free application for Android phones and tablets running on Android and equipped with NFC wireless communication module.
Functions:
* preparation of the clock configuration in offline mode (without the need to connect to the clock)
* setting coordinates by selecting a predefined location (coordinate code), directly pointing to the location on the map on the phone or rewriting the current position recorded by GPS on the phone.
* reading and writing configurations to the controller
* quick programming of multiple controllers with a single configuration
* reading and saving configurations to file
* sharing of configurations via e-mail, bluetooth, network drives, ...
* unambiguous identification of the connected clock and the ability to give devices their own names
* automatic configuration backup. In conjunction with the unique identifier of each clock, you can easily restore the previous configuration
* setting the time and date based on your phone's watch
The app is available on Google Play!
CLOCK TIME CORRECTION - Set monthly correction of system clock seconds.
BATTERY CHARGING INDICATOR - The controller is equipped with a battery status check to keep the clock running in case of main power supply failure. If the battery is low, the user will be notified to replace it.
LCD BRIGHTNESS CORRECTION - Changing the contrast of the display allows the LCD to be read clearly for different viewing angles.
RELAY STATUS MEMORY - The set relay status in manual mode is also remembered after a power failure.

PCZ Configurator

- NFC wireless communication - possibility to read and save the timer configuration wirelessly via an Android phone equipped with an NFC communication module.
- preparation of the timer configuration in offline mode (without the need to connect to the timer)
- reading and writing the configuration to the controller
- quick programming of multiple controllers with a single configuration
- reading and writing the configuration to a file
- sharing the configuration via e-mail, bluetooth, network drives ..
- unambiguous identification of the connected clock and the ability to give devices their own names
- automatic configuration backup. In conjunction with the unique identifier of each clock, you can easily restore the previous configuration
- setting the time and date based on the phone's clock

Technical data